Lowrance Elite Ti2 versus Elite FS

In short, Elite FS has a new screen, new housing and ethernetconnection versus Elite Ti2.

If we start at the back, Elite FS has one more connection versus Elite Ti2, ethernet.

That yellow connector you see there is ethernet. With Elite Ti2 ethernet was only wireless (WIFI), and while that might sound like a good idea, the limitations with WIFI meant that Elite Ti2 could only share 2D and mapping over WIFI as well as synchronizing waypoints and only to another Elite Ti2. You could not share between three units, or between Elite Ti2 and any other series of units. With Elite FS and cabled ethernet, those limitations are gone, and Elite FS will share everything. It can share with another Elite FS, and even with HDS, the top-level unit from Lowrance. 

Cabled ethernet also opens the door for using modules with Elite FS, as a first middle-range unit from Lowrance with such capabilities. We have seen this coming when looking towards Simrad, were GO got cabled ethernet in order to use radar. Elite FS is compatible with Halo (radar), LiveSight, StructureScan 3D, S5100 and any other current module used by Lowrance. Elite Ti2 is not, as it lacks the ethernetconnection needed to use these modules.

One thing that has not changed is the transducer-port. This is still the 9-pin xSonic, and there is only one port. We expect the Y-Cable sold with "Active Imaging 2 in 1" to continue, so you can have separate 2D- and StructureScan-transducers, but the Y-cable does not work with Airmars XID,  meaning you are limited to Lowrance-transducers when using the Y-cable. However, with the ethernetport and support for StructureScan 3D, you can now have both great Side-/DownScan AND great 2D with an Airmar-transducer with Elite FS.

The housing has changed as well, with the same "tail" at the top at the back that we first saw with HDS Live.

The tail covers the new placement of the internal GPS-Receiver, in older generations it was placed alongside the screen. In its new location, it is less prone to be hindered in its "view" to the satellites. In reality, this change means more accurate positioning with Elite FS than with Elite Ti2.

Elite Ti2 (and Ti) had five buttons, Elite FS has six, Power, zoom in and zoom out and Pages, and the new programmable button. Again, something we first saw on HDS Live (12 and 16). This button can be set up to do exactly what you want; examples could be screenshots, spotlock on your TM, dropping the Powerpole etc.

For those of us that prefer both touch and a full set of buttons, HDS is still the only offering from Lowrance.

The screen on Elite Ti2 was the same as on Elite Ti, and again the same as HDS Gen 2 Touch. 

With Elite FS we see a screen very much like HDS Gen 3, glass glued to plastic (instead of plastic glued to plastic on Ti2), with more "punch" in the colors and easier to keep clean. Resolution wise there is no change, and Elite FS is still not on par with HDS Carbon and Live. (Carbon and Live has the exact same screens.)

At the time of writing this, Elite FS is available only in 7 and 9. Not making a 5 is a sensible move by Lowrance, that screen would simply be too small to justify the screen-quality and features on Elite FS. We are a bit surprised to see that there is no 12, but Lowrance made a similar move when they launched Elite Ti, for that series the 12 came a year or so after the smaller sizes. We expect a 12-version of Elite FS to come along as well, if the sales of Elite FS meets their expectations. (Judging by what we have seen so far, it will most likely meet those expectations.)

Out on the water, most users will notice the better screen, and pinch to zoom when using the chartplotter. We also expect that many users with elite FS will get ActiveTarget, a product NOT compatible with Elite Ti2, and that simply excludes Elite Ti2 from any comparison on live-sonar. Many will also enjoy that Elite FS is compatible with autopilot for their outboard, especially anglers that troll or have long stretches of transportation between spots. The last group that will greatly benefit from Elite FS over Elite Ti2, are the users that already have a HDS Gen 3, Carbon or Live and are looking for a second unit to network with their HDS.

As usual Lowrance is keeping information on processor and other components handling the processing in the unit for themselves. But it just takes a few seconds of use to see that Elite FS is significantly faster than Elite Ti2. Elite FS feels a lot like HDS Carbon when flipping through menues.

Software

With added functionality comes software that supports such functionality. With cabled ethernet comes support for modules, with full NMEA2000 comes support for autopilot. With Elite FS being brand new, it will probably be supported with software-updates the next 2-3 years, while Elite Ti2 has most likely seen its last update.

Networking is a big thing with Elite FS, probably THE biggest difference versus Elite Ti2 for most users.

Elite FS does it, Elite Ti2 does not.

For anglers fishing deep, Elite FS now supports up to 1000W (RMS) 2D-transducers. Elite Ti2 was limited to 500W, you could still use popular 1000W-transducers like TM185 and B175 but you could not fire them at full power. With Elite FS, these fantastic transducers can now be used to their full potential for power. What is yet to be explored, is to test if the processing of the 2D-signal on Elite FS has been beefed up as well. With Elite Ti2, there was a noticeable difference in sonar processing for 2D versus HDS, and we are curious to see if that is the case for Elite FS as well. Watch this space for more information on that, as we will be testing Elite FS with several transducers through 2021, also in deep water and with Airmar TM185. 

Airmar TM185HW and Lowrance HST-WSBL.

Transducers

Let us start with what has not changed. Active Imaging was one of two big differences between Elite Ti and Elite Ti2 (the second was WIFI-networking of two Ti2s), and the two Active Imaging transducers continue with Elite FS. The "all in one" transducer Active Imaging 3 in 1 (SKU 000-14029-001) will be the go-to transducer for most users of Elite FS, just like it was for Elite Ti2. For users wanting to combine a shoot-through like PD-WBL (SKU 000-0106-73), Active Imaging 2 in 1 and a Y-cable will still be a very good choice. (More on the difference between those transducers in THIS article).

But with support for 1000W and modules, we will probably see users going all the way on StructureScan using StructureScan 3D (module and transducer) for the best range possible, especially the guys fishing saltwater as SS 3D "punches" through saltwater better than Active Imaging does with  better practical range and more detail, both for SideScan and DownScan. Anyone regularly fishing deeper than 40-ish meters will benefit from SS 3D and Airmar versus the classic AI 3 in 1.

While it is nice to see Lowrance open up their middle-range for anglers venturing into open water, what everyone is looking for is aimed more towards the shallow-water angler, ActiveTarget. 

ActiveTarget and Elite FS in forward view.

For the first time in Lowrance-history, they now have a high-resolution live-sonar to offer their customers, and Elite FS supports it. (Elite Ti/ Ti2 does not.) ActiveTarget has three types of view, here is a brief look at the three:

Forward view:

ActiveTarget Forward view

Down view:

ActiveTarget Down view

Scout view:

ActiveTarget Scout view

While sonar-nerds will probably debate the difference between Garmin LiveScope (LVS32) and ActiveTarget, we will keep it simple and claim that they do the same. From what we have seen so far, the difference between the two are so small that they are merely for theoretical discussion. Indeed well played by Lowrance, but they are a couple of years behind Garmin in this game, and a "Gen 2 LiveScope" can again tip the scale in favor of Garmin. That is the joy of fierce competition.

To sum it up.

Looking for more "VS-articles"?

Lowrance HDS Carbon vs HDS Live

Lowrance Elite Ti vs Elite Ti2

Lowrance Hook2 vs Hook Reveal